Tips For Painting Drywall!

By David Braybrooke -

Painting drywall is a fairly specialized task but with the right equipment, tools and preparation it is one that can be achieved by nearly anyone. The following steps apply:

(1) Drywalling jobs are best done when the weather is fairly warm and not too humid. Make certain that the surface to be painted is dry, clean, and free from oil and grease. Three coats of a joint compound should be applied to the drywall, then the joints between panels need to be taped with paper or fiberglass-mesh tape. This ensures the joint gets surfaced over. Fill in any cracks or marks the same way.

(2) Wiping the dust off walls and ceilings before priming may produce a cleaner finish yet from experience, I would suggest a light sanding with fine grade sandpaper (200 grit) after the prime coat has dried. Any imperfections, raised fibers and rough chips get smoothed off with ease. Wearing goggles and a mask is a good idea when drywalling as gypsum dust can be really irritating and in some people has been known to cause breathing problems and eye infections; always dress in sensible protective clothing.

(3) Before painting get out the vacuum cleaner or hand dust out electrical boxes and take care to remove dust above doorway or window trim. As with any painting job, drop cloths should be used to protect finished floors, doors, windows, taps and any other fixtures, 1-mil plastic or “painter’s plastic” is highly recommended.

(4) Do not let the drywall sit too long after being taped and sanded as sunlight can cause the face paper of the drywall to yellow and fade looking uneven after painting. Use a good-quality latex stain-killing paint before priming to combat yellowing.

(5) Three painting techniques commonly used are to apply with a brush, a roller or by spraying. A brush is fine for cutting in around trim and for fiddly areas like corners. Rollers are great for large areas, the bigger the area to be painted the bigger the roller used should be. Roll the top coat across the direction that the primer coat was applied; this promotes evenness for a great finish. Using a sprayer is a faster technique yet the finish achieved doesn’t always look as uniform and consistent as using a paint roller. A better idea is to use a paint-sprayer followed by a second person who rolls the finish. Makes quick work!

(6) Two coats of paint should be adequate. One trick when it comes to priming drywall is to paint the first coat with a low-sheen, latex flat wall paint, tinted to match the color of the top coat. The problem with using standard ‘primers’ or ’sealers’ or even a good-quality ‘primer-sealer’ is they don’t always adequately cover taped seams and fasteners. You sometimes end up with a bit of a see-through effect which does not look good. It is never a wise idea to skip the first coat as it prepares the surface for the top coat to be applied.

(7) For the top coat, two coatings of a gloss paint (includes satin and eggshell) used for wall surfaces, leaves a finish that is easily washable and not prone to smudges and marks. Bathrooms and kitchens, heavy cleaning areas, are ideal rooms for this. A flat paint is a better option used on the ceiling. A photographing (transparent) effect will be avoided; common with gloss paints.

Take time to prepare your drywall, use good quality painting products and tools and you should end up with an even, impressive-looking finish that will last for years. Consulting a paint specialist at the hardware store before beginning any job will clear up any doubts over which products are the best ones to use. Keep in mind that some jobs may require adjustments to the steps listed in order to achieve the best painting result.

For More Great Articles, Please Visit: http://fatherspirit-mydailybread.blogspot.com/ Thanks! 

Article Source: http://EzineArticles.com/?expert=David_Braybrooke

Drywall Repairs Made Simple

By David Altman -

By the time you finish reading this article, you will be able to perform basic repairs to damaged drywall. There are some basic tools that you should keep around the house, if you have an active family and are prone to get dings in the walls.  This article will not provide enough information to do major repairs to drywall. Major repairs are simple, but you must learn the basics first.

Here is a list of some tools you will need. Your local big box can supply you with some basic tools. They run in price range from cheap to professional quality. They have plastic putty knives for less than a dollar all the way up to stainless steel that with care, will last a lifetime. If you expect a very small number of repairs, the plastic will suffice. Also, get a carriage bolt, a small hammer, a can of drywall joint compound, 150 to 220 grit sandpaper and a paint brush. These basic tools will repair most small dings and dents in drywall.

An example of a ding would be where the locking button on a door knob has left an impression in the wall behind it. This is typical of a quick and easy repair. Look at the damage. Is there anything protruding above the wall surface?  If so, use the carriage bolt to push the protrusion below the wall surface. Use the hammer to help persuade the protrusion to go below the surface of the wall and round the edges. Next, take the putty knife and some joint compound or as it is commonly called, drywall mud, and fill the hole.  Wait until the mud dries, sand lightly and fill the hole again to bring the material to the same level as the wall.  Sand the surface again until the wall is smooth and level. Do not over sand. This will rough up the drywall allowing the paper to fray and requiring more mud to seal the rough surface. There should not be any differences in the surface. Several small applications will last much longer than one large application and give you better results.

Is everything smooth? If not, apply some more drywall mud to even the wall surfaces. Sand again. When the wall is smooth, apply the paint primer. When the paint primer is dry, apply your regular wall paint. The paint primer is to seal the wall so the new paint does not dry too quickly allowing the patch to be visible.

That is the basic method of repairing damaged drywall.

For more in depth instructions on basic drywall repair visit http://www.single-family-home-remodeling.com/drywall-repair.html

Article Source: http://EzineArticles.com/?expert=David_Altman

Drywall Finishing Tips

By Jerry A. Blackburn

Installing drywall is something that takes patience and detail. If you’ve never installed drywall you’d be surprised at how easy it is but how important it is to do correctly. How well you apply the mud will really determine the final look of the walls. Here are some tips to mudding drywall.

Make sure you have the right tools for the job and familiarize yourself with them. These include course taping compound and the smoother topping compound. Other tools include taping knifes, sand paper and putty knives for smoothing surfaces. Jointing compound (the mud) comes in a few different forms. There is powder that needs to be mixed with water and there is pre-mixed, both of which come in different textures.

Before applying the jointing compound, make sure the surface is completely flat and smooth. All the nails and screws should be flush (if not a bit indented) with the wall. You can run a putty knife along the wall to if any nails snag. Putty can be used to smooth out indentations from nails or you can use a bit of the joint compound.

Use the course taping compound to cover the seams and apply the jointing compound to all seams and over tape, nails and screws. Everything must be filled and the surface level and smooth. This coat must dry 24 hours and this process repeated another two times. After each coat, a longer taping knife should be used to smooth the compound to ensure your wall is even and level. It takes a bit of practice and a lot of patience to get the application of the compound right. You have to apply pressure to your knife in different places depending on the angle and amount of compound needed.

Before applying the fourth coat, use your tape knife to scrape an excess dry compound to ensure the surface is completely smooth. Apply the final coat with attention to detail. You may want to thin out your compound stage; it tends to smooth out easier. After the final coat is dry (24 or more hours later) you’ll want to smooth out your surface with the tape knife and sand paper before applying a primer.

The key to mudding [http://www.insidewoodworking.com/drywall/howtoinstalldrywall.html]drywall is patience and that can be difficult since you’re usually at the end of your project and ready to prime and paint your wall. Make sure you do all four coats of compound and wait the 24 hours between applications. After the final coat, make sure everything is completely level and smooth. It may not appear to be a big deal but mistakes will show once you paint or apply wallpaper. Mudding drywall is easy but it takes patience and attention to detail.

Being really interested in drywall and types of drywall, Jerry Blackburn has been publishing many informative papers in this specific area. You might come across his observations on how to install drywall and types of drywall at http://www.insidewoodworking.com

Article Source: http://EzineArticles.com/?expert=Jerry_A._Blackburn http://EzineArticles.com/?Drywall-Finishing-Tips&id=1399340

Maintenance, Repairs and Replacement For Glass Windows and Doors

By  Rob Mainstone

Every house uses glass in some form or the other. Your house too might have doors, windows, partitions, balustrades, shower screens or pool fences made of glass or containing glass to a great extent. The advantage of using glass is that it not only looks good but also requires very little maintenance.

Although glass does not require attention on a daily basis, you should ensure that it is cleaned on a regular basis since being porous it can cause streaks and stains to linger on and become a pain to remove if ignored for a long time. Glass doors and windows are actually very easy to clean. All you need is a bucket of water, a mop, a rubber squeegee and a lint-free cloth, preferably an old cotton t-shirt or towel. You might also need a metal scraper to remove stubborn dirt or paint marks from your glass. Your mop should first be immersed in water and then sprayed with any window cleaning detergent. You can then scrub your glass window or door with the wet mop. Remember to scrub the corners too since they tend to be ignored. Next, take the squeegee and start cleaning your door or window from the top towards the bottom in a sweeping motion. You will need to use your cloth to clean the corners. You can also use diluted vinegar in place of any window cleaning detergent. Repeat the same procedure on both sides of your glass door or window.

While cleaning of your glass windows and doors is a fairly simple job as long as you do not have to climb to a height to clean any fixed windows, repairing or replacing is another matter altogether and best left to the professionals. If your window is cracked due to any accident, then you should get an experienced fitter to inspect and replace it. In the meantime, you can delicately apply masking tape on the cracked glass so that it does not crash and splinter into minute pieces without any warning. Ensure that you get more than one quote but do not base your final decision on the basis of lower rates only. Instead, consider the experience and reputation of the glass expert before you make up your mind. Certain glass items such as leadlight doors and windows will require people who have prior experience in designing, replacing and installing such items. An experienced designer will be able to design and construct a new leadlight based on your ideas and also be able to install it without any fuss.

In addition, glass accessories such as brackets and hinges can also break over a period of time. Often, water might start to seep from the side or under window frames and you might need to seal any gaps that might be facilitating a leak. Again, unless you have prior experience, it is best left to experts to come in and have a look at the leakage and determine the appropriate action.

Thus, in addition to looking smart and providing clean lines to your house, glass doors and windows are also easy to maintain and in the unfortunate event of breakage are also very easy to replace. A little care and time will go a long way in ensuring that your glass doors and windows last for a long-long time.

Rob Mainstone is the owner Perth glass company, West Perth Glass and provides glass repair services for West Australian clients.

Article Source: http://EzineArticles.com/?expert=Rob_Mainstone

How to Hang Drywall - Some Helpful Advice

By Wendy Pan

How To Hang Drywall, Or Not?

Dry ceiling before you drywall. This is literally the top tip when talking about how to hang drywall. Using a long builders’ level, check your wall studs for any warped boards. Only straight flat studs will give you a level surface on which to hang drywall. People, especially the female of the species will quickly spot the bulges if you fail to put furring strips on to the frame around items that may stick out beyond your drywall studs. It’s all in the eye when learning how to hang drywall.

How to hang drywall sheets is horizontally and from the top, down to the bottom. Be sure to draw an outline grid of your studs on the floor. When you want to find them later for hanging pictures on you really don’t want to rely on hammer sonar.

A top tip on how to hang drywall when you are working alone is to hammer four nails in a row into four adjacent studs about 50″ inches from the ceiling. This enables you to lift the sheet (lift and manhandle with a straight back and use your legs only) and rest it on the nails. Hang all of the drywall upper sheets before going onto the lower sheets.

The well-dressed drywall hanger will of course have strong toe-protecting shoes. Line up the fixing screws with your floor grid marks and place screws in the dimpled area of the drywall about 2 inches apart. How not to hang drywall is with the dimpled surface facing inward! Later you will level off the dimples with joint compound.

Around the edge of the drywall sheet, place the screws 3/8″ in from all edges and space them 7″ inches apart. Across the face of each sheet, drive screws into the studs about 12 inches apart. If you miss a stud, and try a bit further over. You can fill the hole with joint compound the drywall hanger’s best friend.

The secret of how to hang drywall successfully is to have the right tools. Use a sharp rotary drill for cutting out shaped holes around light fixtures and windows etc. Loosely fasten the board over the light fixture or window, do the cutting then finish fastening the board. Over a window completely fix the drywall around the edge and then cut out the window.

Try to keep cutting of the drywall to a minimum but when you need to cut a sheet down to size be sure to mark the paper surface correctly. Then cut through the paper face with a clean sharp knife. ALWAYS KEEP FINGERS BEHIND THE CUTTING EDGE! Another top tip on how to hang drywall is to lift the panel up from your working surface and snap it downward along your cut line to break through the core.

When hanging the bottom sections of the drywalls, you do not line up the seams of each sheet. Therefore, start the second row with a half sheet. This will give sturdier and stronger drywall. The tapered edges should always butt together. Cut the panels about 1/2-inch short of the floor to allow for any unevenness in the floor or ceiling. The gaps at the bottom of the wall will be covered with your baseboard.

A final top tip on how to hang drywall when on your own is to raise each panel into place with a pair of foot levers. A sturdy piece of clean wood on top of a small wedge will enable you to lever the drywall sheet into position while you drive the first screws or nails.

Wendy Pan is an accomplished niche website developer and author. To learn more about [http://drywallrepaironline.info/how-to-hang-drywall-some-helpful-advice/]how to hang dry wall, please visit [http://drywallrepaironline.info/]Dry Wall Repair Online for current articles and discussions.

Article Source: http://EzineArticles.com/?expert=Wendy_Pan http://EzineArticles.com/?How-to-Hang-Drywall—Some-Helpful-Advice&id=1528621

By Guy J Morris -

Neither is it easy nor totally impossible as some people would have us believe, for dry walling your home. For dry walling you have to follow a few simple steps. You will need equipment like plaster, patches, paint, hammer, joint putty, scraper, sandpaper, Tray, putty trial, thinner and many other tools to complete the work. It also depends on the size of the area about the exact kind of tools and materials necessary.

Sandpaper will be necessary. Once you start the drywalling process you will need to remove all lumps by giving the walls a thorough sanding until clear white is visible. Use a cloth to complete the procedure by cleaning down the wall by removing any sand particles.

If the wall has holes in it, plaster will get in. So fill in the holes with the scraper and putty trial by applying the joint putty and patch where necessary. When, a second coat of plaster is necessary, repeat the course of action until the hole is filled and scraped down to fineness.

Do not start to drywall until you have sand down the area, smoothed out the surface, and washed the wall, removing any dust particles from the wall. Do make sure that the area is dry, before you sandpaper the same. Follow the drywall method by following the systematic steps shown to you in the kit provided, till you achieve a clear smooth area.

After improving the wall by dry walling, paint it. Choosing the correct brushes and paint suited to the job will help you achieve the best effect. Before you shift around your furniture at home paint the base line area. Let the paint dry and touch up by re-arranging the, curtains and furnisher and other home items.

Dry walling is more time consuming than being difficult.

At times you can get make do with repairs rather than go for a big change. Since the walls are layered, a bit of a plaster and other tools and materials could spruce up the area. But if you have rotted area, you may want to think about other options; else you could hire an expert to get the repair done.

In case you have areas in your home which indicate wear and tear, taking care of the problem immediately can save you many problems later on. Usually a repair work is less troublesome than entire improvements, thus repairs almost always are a cheaper option.

Soon after the spackle is applied, use your sandpaper sand on the area. Use your scraper to remove or clear up the area if you notice any peeling, paint or loose plaster. Once the spackle starts drying and is sanded add a second coating to cover the entire hole. Now sand and prime the patched part. Now, you are ready to paint.

Wasnt that easy?

Being very interested in drywall repair and drywall installation, Guy Morris has been publishing several detailed articles on the subject. You can have a look at his writings on   how to do drywall installation over at http://www.insidewoodworking.com/drywall/howtoinstalldrywall.html and various other sources for how to do drywall installation information.

Article Source: http://EzineArticles.com/?expert=Guy_J_Morris http://EzineArticles.com/?How-to-Drywall-Your-Home-Yourself&id=1533143

Get the Right Drywall Tools

By Robert J. Carlton

Home repair and construction can be difficult enough with the correct tools, but without them, it can be disastrous and time-consuming. This is especially true when you’re talking about drywall tools. Dry walling is a great DIY job with the right drywall equipment. If you don’t have the right tools for drywalling, it may take you twice as long to do the job half as good. If you’re interested in learning more about drywalling, you can find some excellent tutorials and directions online or at your local library. The first thing they will mention, also, is the necessity of having the right drywall equipment before you begin.

Some of the tools you’ll need are trowels-both plaster and corner trowels; a hand sander, sandpaper and block sander; cordless drill for the drywall screws; tape measure; T-square for measuring before cutting; steel knives for putting the tape on the wall and for finishing. In addition to tools, you’ll need supplies as well. Some of the supplies you’ll need before you begin are the paper tape for taping the drywall; drywall sheets; sandpaper in 100 and 220 size; drywall screws, nails, drop cloth and rulers.

If you haven’t hung and taped drywall before, you may want to take a tutorial online or at a workshop. Some home building supply stores offer workshops or short courses as well as brochures on how to work with drywall. Drywall is for your walls and ceilings, both, which are important parts of your home. You’ll want them to look as professional as possible.

You may want to make a sketch or drawing on a piece of paper. Have all the measurements for your room on paper. Drywall comes in 8′ or 12′ length 4′ wide. Since most ceilings are 8 feet high, you’ll be laying the drywall horizontally with two 4′ sheets making up the distance to the 8-foot ceiling. While you may need less sheets with the 12 feet in addition to less nailing and screwing, there is a disadvantage to using the 12 feet drywall. With the 12′ drywall, it’s more awkward to handle and you may have more cutting to do. The staff at your building supply store can give you tips on how to order drywall. If you are drywalling the kitchen or bathroom, you’ll want to get green board, as this is better against moisture.

Always start with the ceiling so you don’t damage a new wall by doing your ceiling. Make sure you measure with your squares before you begin hanging the drywall. When you put in the drywall screws, make sure you indent them so it is easier to fill the holes in with putty. After the drywall is hung, you are ready to begin taping. Good luck! With the right drywalling tools, this should be a breeze.

Rob Carlton frequently writes detailed papers on issues corresponding to how to install dry wall. You can have a look at his contributions on   dry wall over at http://www.insidewoodworking.com/drywall/index.html and different sources for dry wall information.

Article Source: http://EzineArticles.com/?expert=Robert_J._Carlton http://EzineArticles.com/?Get-the-Right-Drywall-Tools&id=1540576

Drywall Finishing For All Homes

By Vince L. Paxton -

Drywall requires mud to finish it and make it look smooth just as many homeowner’s want. it is time consuming but well worth the wait.

Once the drywall is installed and screwed to the wall, it is going to need some tape and compound. This is a very big step as it is the final step in the way that your drywall looks. You must make sure that you are applying the mud or compound the right way to your walls to ensure that it looks great.

There are three steps to know about how to mud drywall.

1.    know what tools you need and what type of compound.
Being prepared is one thing that you have to make sure you are doing. you need to be sure that you are familiar with the items that you have to have.

joint compound will come in two ways, powder and pre mixed. They are going to be different textures. Taping compound is coarse and needs to be used for the initial tape. Topping compound is thin and smooth than regular taping compound. It should be used for finishing.

when applying mud you should use tape knives. These tools will come in different sizes and you should always use on that is a little longer than the first one for each layer that you do.

You want to be certain that all of your screws are sunk in deep. You do not want any protruding out so that you are not hitting them with your knife. You should go back and sink your screws in a little further if they are not in far enough.

2.    you should follow procedure.

When you are mudding drywall it is going to be a 4 step and four day project. You will want to let it dry for at least twenty four hours.

You can start with a   drywall taping layer. You should apply compound and then place paper jointing tape in all the joints and the make it smooth with a little compound. You will also need to cover up all the nail and screws with compound.  You should always make sure that your finish look is completely smooth and looking good.

You will want to apply two layers of compound that will smooth out the surface for you. you will want to use a good tape knife that is one or two inches longer than the one you used before. For the second and the third you will need to use a tape knife that is about seven inches to a foot in length.

You should try and put the compound on the joint and then smooth It with different strokes.

It may be hard to apply this compound. You will want to apply the mud in different variations of thickness. You need to apply pressure in different spots. When you are ding the side strokes you will want to put more pressure on the outer part of the knife. There are different procedures for smoothing and you will need to learn the right way for each method you are doing.

The finish coat is last of course. this is where you need to make sure that it looks good and is smooth.

3.    have some patience on your side

when you are mudding you want to be consistent and take your time. You may want to get it done fast but you have to follow with the stages. You cannot rush the mud to dry. You have to wait and leave the enough drying time in between. This can be messy but it is something that has to be done to make the drywall come out right.

Vince Paxton’s newsletters are found on plenty of online sites with reference to drywall taping tools and how to do drywall taping. Writing for reports such as http://www.insidewoodworking.com/drywall/drywalltaping.html the writer affirmed his depth of understanding on ideas related to drywall taping.

Article Source: http://EzineArticles.com/?expert=Vince_L._Paxton http://EzineArticles.com/?Drywall-Finishing-For-All-Homes&id=1503433

Home Handyman

By Ken Marlborough

Home handymen are professionals who do varied kinds of jobs in domestic households related to electrical installations, plumbing, house renovation, house cleaning, and small construction works. Many home handymen are self-employed and are paid on an hourly basis whereas others work for a contractor or organization that pays fixed monthly salaries.

Home handyman provide assistance in carrying out small to medium level household repair and maintenance jobs such as remodeling the kitchen or bathroom, finishing the attic or basement, installing drywall or ceramic tile, hanging shelves, and building a deck or fence. These jobs are too small for hiring a full time contractor and are normally completed with the assistance of a handyman.

Home handyman use different types of tools and equipment for carrying out their activities. These tools may include insulated tools for carrying out electrical works that can withstand voltage in the range of 1000 volts to 1500 volts. Other tools may include pliers, screwdrivers, knives, scissors, bolt cutters, cable cutters, and hammers. Bags that carry these accessories are made from a combination of cotton cloth, leather, and other strong material to make it long lasting.

People wanting to avail of the services of home handymen can either contact a handyman contractor or find an experienced self-employed handyman who can perform the required job. Contractors usually charge a fixed rate whereas self-employed handyman quote their own hourly rates after assessing the type of work and the labor involved. It is better to hire self-employed handyman as their payment terms can be negotiated.

It is important to assess the work skills and experience of handymen before hiring them. An unskilled handyman can ruin the proposed construction or maintenance work and adversely affect the budget of the homeowner. People can take help from friends and associates in hiring a handyman who has all the required skills and experience for completing the required job. [http://www.z-Handyman.com]Handyman provides detailed information on Handyman, Handyman Services, Starting A Handyman Business, Handyman Tips and more. Handyman is affiliated with http://www.i-Remodeling.com Home Remodeling.

Article Source: http://EzineArticles.com/?expert=Ken_Marlborough http://EzineArticles.com/?Home-Handyman&id=429053

Choosing the Best Way to Fix a Hole in the Wall

By Kurt A. Schefken

When it comes down to having to repair a hole that is in your walls, there are many things that you can do to make the process much easier! Wall repair is indeed a very simple thing compared to other things in your home!

When fixing a hole in the wall, the first thing you must do is determine the size of the hole. By that, there are different methods to use when fixing a specific size of hole. If you have a small hole (such as a nail or small hole), then all you need to use is a patch with a compound mixture. If you have a bigger yet small hole (the size of a light switch hole), you can fill it with paper of any sort; then cover it with the compound mixture. For medium sized holes you will want to use a “hot patch”. By that, you will be filling the hole with drywall and leaving a flap on each side. For large holes, you will want to replace the entire area with new wall; therefore, you will want to take out all the nails/screws and replace the old wall with a new piece of drywall. Then, you can screw it back to the wall, tape the seams, sand the wall and then you can finish it how you want it. Most importantly you will want to make sure that you are using the proper technique for the hole that is in your wall!

Once you have decided on the best technique for the hole that you have, you will want to have all the supplies that you will need; be prepared! By having everything you need; it will save you time later; especially because you will have to work quick when the compounds are mixed and ready to use!

If you are filling a big hole, make sure the drywall is cut and in place before you make any compound up. At that point, you will want to double check the hole size to make the technique your using is the right one; as you don’t want to be almost done and finding out it won’t work.

When compounding, make sure that you use only what you need to; as using too much is not good either. In fact, the secret to using compound is to only use what you have to as well as making it smooth as possible. In the end if you use too much compound it will only result in extra sanding; which may become tiresome! Remember, using it in moderation is the best thing!

When doing any home repair, patience is the thing you must remember! In fact, you must remember to take your time and allowing things to get done at their pace (such as letting the compound dry before sanding). Also, you will want to follow all directions! Giving everything time to dry allows you to have time to clean up any mess that has started.

Even if you think your compound is smooth, it is not! In fact, you do not want to skip this process as it will show once you finish/paint the wall (it may leave ridges or bumps). Also, you will want to clean the area before applying the paint, as well!

Once everything is patched up, you can sit back and enjoy your “new” looking wall!

Being especially passionate about observations bench kits and wooden workbench plans, Kurt Schefken was editing a large number of detailed reports in the area. You can have a look at his publications on comments [http://www.insidewoodworking.com/workclam/workbenchplans.html]bench kits & free workbench plans over at http://www.insidewoodworking.com

Article Source: http://EzineArticles.com/?expert=Kurt_A._Schefken http://EzineArticles.com/?Choosing-the-Best-Way-to-Fix-a-Hole-in-the-Wall&id=1588842